DIY Tub Installation.
DIY Tub Installation.
Blog Article
What are your concepts on How to Install a Bathtub?
Mounting a tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the new one. See to it you have certified on your own for the job and also are comfortable attempting it. As opposed to hiring a service provider to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This article will certainly help you set up a new tub in your shower room if you have actually already acquired a new tub and also do not need to alter the plan of your previous water system pipes.
Your devices and product list should make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the faucet and the sink. Protect the faucet in position with the supplier provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the called for placement. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub till the spirit level reviews level.
To mount taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as check all joints and also new pipework for leakages and tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the bathtub has been made use of a minimum of once as this will certainly settle it right into its final position.
Getting ready for the Installation
First of all, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a rigid seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also installations. They are offered in tubes and cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to permit the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our part about Installing A Bathtub. Thanks a ton for spending some time to browse our posting. Are you aware of someone else who is sincerely interested in the topic? Feel free to promote it. Kudos for your time. Come back soon.
Book Today! Report this page